By Plumbing Guide for Installing a Bathtub
By Plumbing Guide for Installing a Bathtub
Blog Article
The content down below relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is exceptionally compelling. Don't skip it.
Setting up a tub isn't precisely rocket science, but it does need strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably hard project. If the old bathtub is readily available, the task can move quickly; if you need to open up a wall surface to get rid of the old tub and place the brand-new bathtub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as embeded in the brand-new one. Ensure you have actually certified yourself for the job as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly help you set up a new bathtub in your restroom if you have currently bought a brand-new tub and do not need to change the setup of your previous water pipes.
Your tools and material list must consist of the following:
Preparing for the Setup
Firstly, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to avoid stress on the bathtub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be quite bothersome because of the limited gain access to that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, put the tub in the called for setting. The wood boards are handy in evenly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bath tub up until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water and also check all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the tub and also inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, fix the bath paneling as described in the producer's user's manual. Tiling as well as securing around the tub must wait up until the bathtub has actually been used at the very least once as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Protect the faucet in position with the maker provided backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind ought to be connected to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, creating the water to pass through the wall surface between the bathroom and the tiling, leading to complications with dampness and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealer can split relatively early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily readily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very eager about A Step-by-Step Guide to Installing a Bathtub and I'm hoping you liked the entire blog entry. Are you aware of another individual who is interested in the niche? Please feel free to share it. Thanks so much for taking the time to read it.
View More Report this page